Overton Power Washing logoOVERTON
Field guide · Central Texas driveways

Know your driveway

Plain concrete can take serious pressure. Stamped concrete, pavers and stone can be ruined by it. Find your surface below to see how it should be cleaned.

The 7 surfaces

Ranges adjusted on site for age and condition

Broom-finish concrete

2,500–3,500 PSI

The most common driveway in Round Rock and Georgetown: plain gray concrete with a lightly brushed texture. It's tough and handles the most pressure.

How we clean it
Pre-treat oil spots with a degreaser and mildew with a cleaning solution, then clean with a rotary surface cleaner for even, streak-free results. Finish by rinsing the edges and expansion joints.
Avoid
Holding a narrow tip close to the surface. It can etch lines into the concrete. Brand-new concrete should cure about a month before its first wash.
Aftercare
An optional penetrating sealer helps it resist oil and mildew. Wash yearly.

Stamped or colored concrete

1,500–2,500 PSI

Concrete pressed to look like stone, brick or slate, usually tinted and coated with a glossy sealer. The sealer is what you're protecting.

How we clean it
Soft-wash with a cleaning solution to lift dirt and mildew, then rinse with a wide fan tip at lower pressure. Work with the pattern, not against it.
Avoid
High pressure and harsh chemicals. Both strip the sealer and fade the color, leaving blotchy patches.
Aftercare
Reseal every 2–3 years to keep the color rich and protect against stains.

Exposed aggregate

2,000–3,000 PSI

Concrete with the top layer washed away to show pebbles and small stones. It hides dirt well, but grime collects between the stones.

How we clean it
Pre-treat, then use a surface cleaner or wide fan tip held at a safe distance to clean between the stones without loosening them.
Avoid
Concentrated pressure in one spot. It can knock stones loose and leave pits.
Aftercare
A sealer locks the stones in place and brings back their natural color.

Concrete pavers

1,500–2,500 PSI

Interlocking blocks set on sand. Popular in newer neighborhoods. The joints between pavers matter as much as the pavers.

How we clean it
Clean the surface at moderate pressure with the spray angled across the joints, not into them. Pull weeds and moss from the joints first.
Avoid
Blasting straight into the joints. It washes out the sand, which leads to weeds, ants and shifting pavers.
Aftercare
Re-sand the joints with polymeric sand, then seal. This locks pavers together and keeps weeds out.

Brick pavers

1,200–2,000 PSI

Clay brick driveways and walkways. Classic look, but older brick and mortar joints can be soft.

How we clean it
Low pressure with a wide fan tip plus a cleaning solution for moss and mildew. Rinse well.
Avoid
High pressure on mortar joints and acid cleaners, which can damage brick and mortar.
Aftercare
Check and repair loose joints. Seal if you want to limit moss and staining.

Asphalt

1,200–1,500 PSI

Black-top driveways, more common on rural properties around Williamson County. Asphalt is softer than concrete.

How we clean it
Low pressure with a degreaser on oil and gas spots. Keep the nozzle moving.
Avoid
High pressure, which can loosen the surface gravel and open small cracks.
Aftercare
Let it dry fully, fill cracks, then sealcoat every 2–3 years to protect it from the Texas sun.

Flagstone and natural stone

Soft wash, under 1,200 PSI

Limestone and flagstone are popular in Central Texas for walkways, patios and driveway borders. Limestone is soft and reacts to acids.

How we clean it
Soft wash: a stone-safe cleaning solution with gentle, low-pressure rinsing.
Avoid
Acid-based cleaners and rust removers on limestone. They can etch and dull the stone. Also avoid high pressure on soft or flaky stone.
Aftercare
A breathable stone sealer helps resist stains and mildew.

Stains & fixes

Pressure alone won't remove most of these

Oil & grease

Cars, mowers, grills

Degreaser left to soak, then a hot or high-pressure rinse. Old stains may lighten rather than disappear.

Mildew & algae

Shade, sprinklers, humidity

A cleaning solution that kills the growth, then a rinse, so it comes back slower.

Rust spots

Fertilizer, well water, metal furniture

A dedicated rust remover. Regular cleaners and bleach won't touch it.

Oak tannin

Live oaks, leaves, acorns

A cleaning solution and rinse. Usually comes right out.

Red dirt

Storm runoff, flower beds

Pressure washing, sometimes with a pre-treatment for older stains.

Tire marks

Hot tires on hot concrete

Degreaser and a surface cleaner.

Not sure what you have?Send a photo of your driveway with your quote request and we'll tell you the type and the right way to clean it.

Send a Photo

Questions

What PSI should I use to pressure wash my driveway?

It depends on the surface. Plain broom-finish concrete handles about 2,500–3,500 PSI. Stamped concrete and pavers need about 1,500–2,500 PSI, asphalt about 1,200–1,500, and natural stone should be soft washed.

Can pressure washing damage stamped concrete?

Yes, if the pressure is too high. It can strip the sealer and fade the color. Stamped concrete should be soft washed and rinsed at lower pressure, then resealed every 2–3 years.

Will pressure washing remove oil stains from my driveway?

Pressure alone usually won't. Oil needs a degreaser that soaks in first. Fresh stains come out best; old, deep stains can be lightened but may not disappear completely.

How long should I wait to pressure wash new concrete?

Let new concrete cure for about a month before its first pressure wash.

Cleaned the right way

Driveway cleaning is $300 · Round Rock, Georgetown & Williamson County

(512) 803-7336